Error Messages |
Fatal System Errors |
9000 | System Kernel Fault |
9001 | Run Time System Error |
9002 | Unexpected Exception |
9003 | PROM Sumcheck Failure |
9004 | RAM Check Failure |
9005 | Serial Interface Fault |
9006 | Option Test Failure |
9007 | Unknown Engine Instruction |
| |
Recoverable Errors |
List of Execution Errors |
1000 | EXE queue empty when recalled |
1001 | Option not installed |
1002 | Calibration disabled |
1005 | Input Zero not allowed in Ratio |
1007 | Data entry error |
1008 | Must be in AC Function |
1010 | Divide-by-zero not allowed |
1012 | No more errors in list |
1013 | Data out of limit |
1014 | Illegal Range/Function combination |
1015 | Command allowed only in Remote |
1016 | Not in Special Calibration |
1021 | Test not allowed when Cal enabled |
1024 | Illegal Range/Input Combination |
1025 | Auto not available in Tru ratio |
1026 | Probe identity unrecognized |
1027 | Input Zero not allowed in PRT |
1028 | Only allowed in Voltage function |
1029 | Scan modes not allowed in PRT |
1030 | Scan modes not allowed in ACI/DCI |
1031 | 4wV not available via rear input |
1032 | Input Zero not allowed in Cal |
1033 | Calibration not allowed in PRT |
1034 | PRT Ceof Limit @ a+, b+, c+ a-, b-, c- |
1035 | Cannot edit the default PRT |
1036 | Block or Rolling average required |
| |
External Calibration Operations |
Correction Errors |
2000 | Zero Correction Error |
2001 | Gain+ Correction Error |
2002 | Gain- Correction Error |
2003 | HF trim Correction Error |
2004 | Input Correction Error |
2005 | LoI Zero Correction Error |
2006 | LoI Gain Correction Error |
2008 | A to D Correction Error |
2010 | Frequency Correction Error |
2011 | DAC Correction Error |
2012 | Standardise Error |
2025 | Error During HiV Lin Read |
2026 | Error During HiV Lin Calc |
2027 | Error During 2wr Ohms Calc |
| |
Corruptions |
2014 | Serial Number Corrupt |
2015 | Cal Due Date Corrupt |
2017 | Bus Address Corrupt |
2018 | Line Frequency Corrupt |
2020 | Measurement Corrections Corrupt |
2021 | Measurement Corrections Invalid |
2022 | NV RAM Write Failure |
| |
Micellaneous |
2109 | Bad Data from Analog Sys |
2022 | NV Ram write failure |
2023 | Engine — Load factor err |
2024 | Engine — Store factor err |
| |
DC VOLTS |
2101 | Main Ref Check |
2101 | 6.2V Ref Check |
2201 | 100mV Range Zero Check |
2211 | 1V Range Zero Check |
2221 | 10V Range Zero Check |
2231 | 100V Range Zero Check |
2241 | 100mV Range Positive Gain Check |
2251 | 100mV Range Negative Gain Check |
2261 | 1V Range Positive Gain Check |
2271 | 1V Range Negative Gain Check |
2281 | 10V Range Positive Gain Check |
2291 | 10V Range Negative Gain Check |
2301 | 100V Range Positive Gain Check |
2311 | 100V Range Negative Gain Check |
| |
DC CURRENT |
2401 | 100SA DC Range: Zero Input Check |
2411 | 100SA DC Range: 100SA Input Gain Check |
2421 | 1mA DC Range: Zero Input Check |
2431 | 1mA DC Range: 1mA Input Gain Check |
2441 | 10mA DC Range: Zero Input Check |
2451 | 10mA DC Range: 10mA Input Gain Check |
2461 | 100mA DC Range: Zero Input Check |
2471 | 100mA DC Range: 100mA Input Gain Check |
2481 | 1A DC Range: Zero Input Check |
2491 | 1A DC Range: 100mA Input Gain Check |
| |
AC CURRENT |
2501 | 1mA AC Range: Zero Input Check |
2511 | 1mA AC Range: 1mA Input Gain Check |
| |
RESISTANCE |
2601 | Follower Offset Check |
2611 | Follower 100mA Output Check |
2621 | Follower 10mA Output Check |
2631 | Follower 1mA Output Check |
2641 | 3.0V Clamp Check |
2651 | 6.7V Clamp Check |
2661 | 27V Clamp Check |
2671 | Current Sink Clamp Check |
2681 | 10SA Current Sink and Follower 10V Output Check |
2691 | 1SA Current Sink Check |
2701 | 100nA Current Sink Check |
2711 | 10nA Current Sink Check |
2721 | HV Ohms Follower Offset Check |
2731 | HV Ohms Follower Output Current Check |
2741 | HV Ohms Output Voltage and 240V Clamp Check |
| |
AC VOLTS |
2801 | 100mV AC Range: Zero Input Check |
2811 | 100mV AC Range: +179mV DC Input Checks at PreAmp Output |
2821 | 100mV AC Range: -179mV DC Input Checks at PreAmp Output |
2831 | 1V AC Range: Zero Input Check |
2841 | 1V AC Range: +993mV DC Input Checks at PreAmp Output |
2851 | 1V AC Range: -993mV DC Input Checks at PreAmp Output |
2861 | 1V AC Range: +993mV DC Input Checks at RMSConverter Output |
2871 | 1V AC Range: -993mV DC Input Checks at RMSConverter Output |
2881 | 10V AC Range: Zero Input Check |
2891 | 10V AC Range: +9.78V DC Input Checks at PreAmp Output |
2901 | 10V AC Range: -9.78V DC Input Checks at PreAmp Output |
2911 | 100V AC Range: Zero Input Check |
2921 | 100V AC Range: +9.78V DC Input Checks at PreAmp Output |
2931 | 100V AC Range: -9.78V DC Input Checks at PreAmp Output |
2941 | 1000V AC Range: Zero Input Check |
2951 | 1000V AC Range: +9.78V DC Input Checks at PreAmp Output |
2961 | 1000V AC Range: -9.78V DC Input Checks at PreAmp Output |